# ESP32-C6 CSI Node — Target overlay (ADR-110)
#
# Auto-applied by ESP-IDF when CONFIG_IDF_TARGET=esp32c6.
# Layered on top of sdkconfig.defaults — only the differences live here.
#
# Build:
#   idf.py set-target esp32c6
#   idf.py build
#
# Hardware: stock ESP32-C6 dev board with 4 MB or 8 MB embedded flash.
# Confirmed on COM6: ESP32-C6 (QFN40) rev v0.2, 8 MB flash, 320 KiB SRAM.

# ── Target ──
CONFIG_IDF_TARGET="esp32c6"

# ── Flash & partitions (4 MB — common across C6 dev boards) ──
CONFIG_PARTITION_TABLE_CUSTOM=y
CONFIG_PARTITION_TABLE_CUSTOM_FILENAME="partitions_4mb.csv"
CONFIG_ESPTOOLPY_FLASHSIZE_4MB=y
CONFIG_ESPTOOLPY_FLASHSIZE="4MB"

# ── CSI (required) ──
CONFIG_ESP_WIFI_CSI_ENABLED=y

# ── ADR-110 P2 & P3: Wi-Fi 6 / iTWT ──
# IDF v5.4 exposes neither ESP_WIFI_11AX_SUPPORT nor ESP_WIFI_ITWT_SUPPORT as
# user Kconfig — they're SoC capabilities (SOC_WIFI_HE_SUPPORT) auto-enabled
# on chips that have HE support (C6/C5). WPA3 is opt-in:
CONFIG_ESP_WIFI_ENABLE_WPA3_SAE=y

# ── ADR-110 P4: 802.15.4 + OpenThread (MTD) ──
# IEEE 802.15.4 PHY + OpenThread Minimal Thread Device for mesh time-sync.
# MTD is lighter than FTD (no router/leader code) — perfect for sensor nodes.
CONFIG_IEEE802154_ENABLED=y
CONFIG_OPENTHREAD_ENABLED=y
CONFIG_OPENTHREAD_MTD=y
CONFIG_OPENTHREAD_FTD=n
CONFIG_OPENTHREAD_RADIO=n
# Disable joiner / commissioner — we use a pre-shared network key in NVS.
CONFIG_OPENTHREAD_JOINER=n
CONFIG_OPENTHREAD_COMMISSIONER=n

# ── ADR-110 P5: LP-core (deep-sleep coprocessor) ──
# Enable the LP RISC-V core so c6_lp_core.c can ship a wake-on-motion stub.
CONFIG_ULP_COPROC_ENABLED=y
CONFIG_ULP_COPROC_TYPE_LP_CORE=y
CONFIG_ULP_COPROC_RESERVE_MEM=8192

# ── No display, no WASM, no mmWave on the C6 research target ──
# Display (ADR-045) needs 8 MB + native USB-OTG framebuffer hooks.
# WASM3 (ADR-040) needs PSRAM for hot-loadable modules.
# mmWave (Seeed MR60BHA2 on COM4) is a separate board.
# CONFIG_DISPLAY_ENABLE is not set
# CONFIG_WASM_ENABLE is not set

# ── Compiler ──
CONFIG_COMPILER_OPTIMIZATION_SIZE=y

# ── Logging ──
CONFIG_BOOTLOADER_LOG_LEVEL_WARN=y
CONFIG_LOG_DEFAULT_LEVEL_INFO=y

# ── lwIP / FreeRTOS — same as S3 path ──
CONFIG_LWIP_SO_RCVBUF=y
CONFIG_ESP_MAIN_TASK_STACK_SIZE=8192
CONFIG_FREERTOS_TIMER_TASK_STACK_DEPTH=8192

# ── Power: keep CPU at max 160 MHz (C6 ceiling) for DSP throughput ──
CONFIG_ESP_DEFAULT_CPU_FREQ_MHZ_160=y
CONFIG_ESP_DEFAULT_CPU_FREQ_MHZ=160